Digi DC-300 Manuel d'instructions Page 33
- Page / 113
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Digitronic Digital Cam Switch Unit
Automationsanlagen GmbH CamCon DC300
7. Operation of the CamCon
.
7.1. The main menu
The programming always starts at the main menu. No
matter in which state of programming you are, you can
always reach the main menu by pressing the key
(several times, if necessary).
By pressing the corresponding number or by selection
with keys and and a verification with the key,
you can enter the submenus.
7.2. The standard display
You reach the submenu for the display for normal operation of the cam controller via the main menu
point "Visual mode" or by pressing the key (at the main menu).
In the display menu, the active program number, the
relative speed as a bar (e.g. for an analog speed output)
and the current actual position, respectively the absolute
speed (with higher rotational numbers), are displayed.If
the measuring system is put into a slow motion the
respective actual position is shown on the display. With
increasing rotation velocity the device switches at a
defined point (5%) to a display showing the current speed
in the desired representation; a negative direction in the
rotation is shown through a negative sign in front of the
displayed value.
The configuration of the speed display is done in the system setting menu. Here you can e.g. disable
the automatic change of the display, by selecting a certain display type (see chapter "7.4.3. The speed
adjustment" on page 60).
7.2.1. Changing the display
If you want to receive status information of in- and outputs during operation, you can switch through the
several status displays, using keys and . The display then shows an outline of operation for
inputs and outputs:
Output display Input display
As soon as an in- or output activates, its field on the display turns black.
In the lower righthand corner of the display, you can see the current position or the absolute speed at a
faster movement.
Version: 25.02.2014 Page: 33
- CamCon DC300 1
- For your attention 2
- 1. Introduction 7
- 2. Operating Pinciples 8
- 2.1. Speed Compensation 9
- Verlauf Nocke 1 Nocke 2 12
- 2.2. Time - Cam 13
- 3. Assembly 14
- 3.1. Measurements 15
- 4. Electrical connections 16
- 4.9. The measuring system 21
- 4.10. The outputs 25
- 4.11. The inputs 25
- 4.13. Status displays 26
- 4.13.1. Status LED 26
- 5.1. Outline of key functions 28
- 5.2. Menu selection 28
- 5.4. Text input 29
- 6. Initial Operation 30
- 7. Operation of the CamCon 33
- 7.1. The main menu 33
- 7.2. The standard display 33
- 7.2.1. Changing the display 33
- 7.2.2. Program change 34
- 7.2.3. Program name 34
- 7.3. Cam programming 35
- 7.3.5. Programming Time-Cams 37
- 7.3.7. Cam Input 38
- 7.3.8. Adding cams 39
- 7.3.9. Cam Teach - In 39
- 7.3.10. Cam Search 39
- 7.3.11. Cam deletion 40
- 7.3.14. Shifting cam tracks 41
- 7.3.15. Deleting programs 42
- 7.3.16. Copying programs 42
- 0° 90° 180° 270° 360° 46
- 7.4.1. Measuring system 48
- 7.4.1.4. The electronic gear 50
- 7.4.2. The measuring offset 58
- 7.4.3. The speed adjustment 60
- 7.4.3.1. The speed factor 60
- 7.4.3.5. Display, Type 61
- 7.4.4.1. The cable length 62
- 7.4.5. The special outputs 63
- 7.4.5.2. The security output 63
- 7.4.5.2.2. Direction output 64
- 7.4.5.2.4. The hysteresis 64
- 7.4.7. Masterprogram 69
- 7.5. Unit configuration 70
- 7.5.1. User key allocation 70
- 7.5.2. Complete deletion 72
- 7.5.3.2.1. PLC Logic Module 74
- 7.5.3.3. Analog outputs 76
- 7.5.4. Language 78
- 7.5.5. Configure user 78
- 7.5.5.1. User text 78
- 7.5.6. Configure Hardware 79
- 7.5.6.3. CP16 Module 80
- 8. Device info 81
- 8.1. Stack Info 83
- 10. Menu outline 88
- 13.3. OB1 92
- 13.4. FB51 - Main Module 92
- 13.4.1. Parameter of the FB51 93
- 13.5. FC51 - I/O Copy Program 96
- 13.7. OB100 - Startup block 96
- 13.9.1. DBxx range 1 = Status 97
- 15. Possible commands 102
- 15.1. Request on 0x01 102
- 15.8. RK512 Commands 105
- 17. Key word table 109
Produits connexes et manuels pour Balance de cuisine Digi DC-300
(23 pages)
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.926 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels