Digi Digi One EM Guide d'installation Page 39
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
revert
Chapter 2 Command Descriptions 39
revert
Devices
supported
This command is supported in all Digi Connect Family devices.
Purpose Sets a particular group of a devices’ settings to its default values.
If you enter "revert user," "revert group," or "revert permissions," a
message is displayed indicating that those settings cannot be reverted
individually, and instead must be reverted all together at the same time via
the “revert auth” command. The “revert auth” command (revert
authentication and authorization) reverts all users, all groups, and all
permissions at the same time.
Required
permissions
No “set permissions” option is required for all “revert” command variants
except “revert all.” The permissions used by the various “set” commands
apply to the various “revert” command variants. “revert all” uses a different
mechanism that bypasses the individual “set” commands, and therefore
has its own permissions. To execute the “revert all” command, a user must
have permissions set to “set permissions revert-all=execute”. See "set
permissions" on page 86 for details on setting user permissions for
commands.
Syntax
revert [all|accesscontrol|alarm|auth|autoconnect [port=range]|
buffer [port=range]|
devicesecurity|forwarding|gpio|host|menu|mgmtconnection|
mgmtglobal|mgmtnetwork|nat|network|pmodem [port=range]|
|pppoutbound [port=range]|
profile [port=range]|serial [port=range]
service|snmp|system|tcpserial [port=range]|term [port=range]|
udpserial [port=range]|user|wireless]
Options all
Reverts everything except network settings.
alarm
Reverts the alarm settings configured by the “set alarm” command.
accesscontrol
Reverts the access control settings configured by the “set accesscontrol”
command.
auth
Reverts the permission settings configured by the “set permissions”
command, the user settings configured by the “set user” command, and
group settings, configured by the “set group” command.
autoconnect [port=range]
Reverts the Autoconnect settings configured by the “set autoconnect”
command.
buffer [port=range]
Reverts the port-buffering settings configured by the “set buffer”
command.
- Digi Connect 1
- Contents 3 3
- 4 Contents 4
- Introduction 5
- Feature/Task Commands 6
- Basic Command Information 9
- Access the Command Line 11
- Configure an IP Address 11
- Introduction 12
- Command Descriptions 13
- Reboot the device server 15
- Close the current session 17
- Close all active sessions 17
- Device statistics 26
- Statistic Description 27
- IP statistics 28
- Display ICMP statistics 32
- Change Telnet options 34
- Display Telnet options 34
- Turn on binary mode 34
- Add line feed characters 34
- Display operating options 34
- Specify a simple ping 36
- Reconnect to port 1 38
- Reconnect to session 1 38
- [ip_address] 42
- [subnmask[1-32]=mask] 44
- Set access control settings 45
- Set alarms in GPIO mode 46
- Set alarms in match mode 46
- Set an alarm to “on” state 50
- Set alarm mode to GPIO mode 50
- Configure autoconnect 51
- Display autoconnect settings 51
- Configure port buffering 55
- Configure buffers 56
- Set device security settings 59
- Set forwarding settings 62
- Display forwarding settings 62
- Enable IP forwarding 62
- Configure GPIO pins 63
- Add a group 65
- Remove a group 65
- Display the current host name 68
- Updating Global Settings 69
- Adding/Updating Custom Menus 69
- [lkaupdateenabled={on 74
- "revert" on page 39 76
- Set the device id 77
- Commands without permissions 86
- Syntax Set permissions 87
- Set group permissions 101
- Set user permissions 101
- Configure modem emulation 102
- Display PPP outbound settings 104
- Turn on off RCI serial mode 113
- Enable or disable RTS toggle 114
- Set SNMP settings 120
- Display current SNMP settings 120
- Configure terminal settings 126
- Configuring Wireless Settings 136
- Inner and outer protocols 138
- Configure wireless settings 139
- Display wireless settings 139
- #> set wlan wepmode=128bit 143
- Command Descriptions 146
- Modem Emulation Commands 151
- User Scenario - Diagram A 152
- User Scenario - Diagram B 153
- RING and the 154
- S-Register Definitions 159
- Modem Emulation Commands 160
- Result Codes 161
- 168 Index 168
- Xon/Xoff 117 168
Produits connexes et manuels pour Mise en réseau Digi Digi One EM
Mise en réseau Digi XPress Spécifications
(143 pages)
(143 pages)
(2 pages)
Mise en réseau Digi 34 Manuel d'utilisateur
(13 pages)
(13 pages)
Mise en réseau Digi CM Guide de l'utilisateur
(202 pages)
(202 pages)
Mise en réseau Digi 34 Spécifications
(148 pages)
(148 pages)
Mise en réseau Digi M10 Spécifications
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels