Digi Digi One EM Guide d'installation Page 40
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
revert
40 Chapter 2 Command Descriptions
devicesecurity
Reverts the Connectware Device Protocol device security settings
configured by the “set devicesecurity” command.
forwarding
Reverts the port-forwarding settings configured by the “set forwarding”
command.
gpio
Reverts the GPIO settings configured by the “set gpio” command.
host
Reverts the host name set by the “set host” command.
menu
Reverts the custom menu settings configured by the “set menu”
command.
mgmtconnection
Reverts the Connectware Device Protocol connection settings
configured by the “set mgmtconnection” command.
mgmtglobal
Reverts the Connectware Device Protocol global settings configured by
the “set mgmtglobal” command.
mgmtnetwork
Reverts the Connectware Device Protocol network settings configured by
the “set mgmtnetwork” command.
nat
Reverts the Network Address Translation (NAT) and port/protocol
forwarding settings configured by the “set nat” command.
network
Reverts the network settings, configured by the “set network” command,
and the wireless configuration settings, configured by the “set wlan”
command.
pmodem [port=range]
Reverts the modem emulation settings, configured by the “set pmodem”
command.
pppoutbound [port=range]
Reverts the Point-to-Point Protocol (PPP) outbound connection settings,
configured by the “set pppoutbound” command.
profile [port=range]
Reverts the profile settings configured by the “set profile” command.
serial [port=range]
Reverts the serial settings configured by the “set serial” command.
service
Reverts the service settings configured by the “set service” command.
snmp
Reverts the SNMP settings configured by the “set snmp” command.
- Digi Connect 1
- Contents 3 3
- 4 Contents 4
- Introduction 5
- Feature/Task Commands 6
- Basic Command Information 9
- Access the Command Line 11
- Configure an IP Address 11
- Introduction 12
- Command Descriptions 13
- Reboot the device server 15
- Close the current session 17
- Close all active sessions 17
- Device statistics 26
- Statistic Description 27
- IP statistics 28
- Display ICMP statistics 32
- Change Telnet options 34
- Display Telnet options 34
- Turn on binary mode 34
- Add line feed characters 34
- Display operating options 34
- Specify a simple ping 36
- Reconnect to port 1 38
- Reconnect to session 1 38
- [ip_address] 42
- [subnmask[1-32]=mask] 44
- Set access control settings 45
- Set alarms in GPIO mode 46
- Set alarms in match mode 46
- Set an alarm to “on” state 50
- Set alarm mode to GPIO mode 50
- Configure autoconnect 51
- Display autoconnect settings 51
- Configure port buffering 55
- Configure buffers 56
- Set device security settings 59
- Set forwarding settings 62
- Display forwarding settings 62
- Enable IP forwarding 62
- Configure GPIO pins 63
- Add a group 65
- Remove a group 65
- Display the current host name 68
- Updating Global Settings 69
- Adding/Updating Custom Menus 69
- [lkaupdateenabled={on 74
- "revert" on page 39 76
- Set the device id 77
- Commands without permissions 86
- Syntax Set permissions 87
- Set group permissions 101
- Set user permissions 101
- Configure modem emulation 102
- Display PPP outbound settings 104
- Turn on off RCI serial mode 113
- Enable or disable RTS toggle 114
- Set SNMP settings 120
- Display current SNMP settings 120
- Configure terminal settings 126
- Configuring Wireless Settings 136
- Inner and outer protocols 138
- Configure wireless settings 139
- Display wireless settings 139
- #> set wlan wepmode=128bit 143
- Command Descriptions 146
- Modem Emulation Commands 151
- User Scenario - Diagram A 152
- User Scenario - Diagram B 153
- RING and the 154
- S-Register Definitions 159
- Modem Emulation Commands 160
- Result Codes 161
- 168 Index 168
- Xon/Xoff 117 168
Produits connexes et manuels pour Mise en réseau Digi Digi One EM
Mise en réseau Digi XPress Spécifications
(143 pages)
(143 pages)
(2 pages)
Mise en réseau Digi 34 Manuel d'utilisateur
(13 pages)
(13 pages)
Mise en réseau Digi CM Guide de l'utilisateur
(202 pages)
(202 pages)
Mise en réseau Digi 34 Spécifications
(148 pages)
(148 pages)
Mise en réseau Digi M10 Spécifications
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels